Ham Software for Mobira(TM) MD50/MD59/ME59 phones. (Mobira seems to be a trade mark of Mobira) RTFM by OH3NWQ 08.02.2000 Change history: v. 2.09 - PIN code can be defined at compile time - if not, default 3694 is used new defines PIN_1 PIN_2 PIN_3 and PIN_4 (E.g. -DPIN_1=4 -DPIN_2=7 -DPIN_3=1 -DPIN_4=1 to use PIN 4711 ) - R -> not D/S as it should when not scanning ok 2.081 v. 2.08 - new scanning algoritm M(R)(S) ok 2.08 - memory saving seems to be now out of order... error 2.06 -> ok 2.o78 - @ mem scan: R -> Rep/Simp ??? ok 2.07P - rejects at memory scan working ok 2.07L - simplex scanning limits changed in Finnish version ok 2.076 - corrected errorneous scanning after 81# or 82# ok 2.074 - new define NOHIPOWER to disallow the 3rd power step ok 2.06 v. 2.05 - corrected defines - now both X81 and X126 work v. 2.03 - preparations for memory scanning - PIN code (default is 3694) asked at boot if PIN defined ok v 2.03E v. 2.02 - after command 70# you'll see: Stored 1 v. 2.01 - ME59 might work now... forgot the define STEP125 in makme59 file... v. 2.00 - 10 memories 0#, 1#, ... 9# - store last dialed memory with 70#, 71#, ... 79# ( E.g. to store 433775 to memory 1 dial 33775 71# or 3375# 71# or 375# 71# ) - new commands 69# and 99# (:-P) v. 1.86 - 84# command / T on display: lights the keypad and display permanently, when set v. 1.85 - another set of cosmetics - Keypad and display light up when handset is lifted (CU59) - On CU59 <- is shown on display when battery voltage goes below the preset range v. 1847 - cosmetic changes - 12.5 kHz step not yet implemented - 81#-83# commands not yet implemented, but R, S and T toggle on display is. - 81# toggle include repeater channels in scan (R) on display - 82# toggle include simplex channels in scan (S) on display - 83# toggle include memory channels in scan (T) on display - new define STEP125 for 12.5kHz step on MD5x - 12.5 kHz step operation needs an HW modification - new define DOUBLESTEP for MD5x with 12.5kHz to step 25kHz with up and down keys - bYE-bYE 73 text on shutdown v. 1821 - ME59 X126 1.81 seemed to go up on frequency, it should go down on rx - corrected ok v.21 v. 1811 -ME 59 offset vco 126.0/81.0 MHz (not tested) ok v.05 -show D at boot if German repeater band is defined ok v.01 -corrected the missing last channel from MD5x and German repeater band -89# shows the offset vco/xtal, defined repeater band, handset and selected band ok v.10 E.g. 214F59 or 126G53 FinLAnd Euro v. 1.735 -the repeater beep delay that was introduced in v 1.4 is taken away as it did not help at all... -clear scanner rejects 85# ok v.10 -display test with 88# ok v.20 -repeater duplex 7.6/1.6 MD5x 87# ok v.30 28.0/6.0 ME59 ok v.35 -GERMAN now defines the German repeater band -positive/negative duplex toggle 89# ok v.3E v. 1.623 -if SPTT is defined, S button for PTT (CU59) -if REP76 is defined, the repeater shift is 7.6 @ 438.550-439.400 (MD) -if FINHAM is defined, only 432-438 band is available for tx (MD) -4 digit version number for debugging purposes (MD) -CALL led shows that repeter beep is emitted Repeater offset display (on the right upper part of the display - handset CU59): ___________________md5x____________me59______________ S = simplex = simplex D = - 1.6 = - 6.0 D F = + 1.6 = + 6.0 not functional yet D< = - 7.6 = - 28.0 D< F = + 7.6 = + 28.0 not functional yet Scanner information and light status (on the left upper part - handset CU59): R S T R = repetear channels included in scan S = simplex channels included in scan T = lights on permanently (when battery operated) <- Battery voltage has dropped below the preset limit key There are locked/rejected channels in scan o-o Handset is off the hook Boot text: For example if the boot text is RST 173-EU 314 990402 rst = reset 173 = version 1.73 (fourth number used on betas and intermediate releases) EU = European band (FI for Finnish) 314 = modulator xtal = 31.4 MHz (On ME59 this is the VCO freq) 990402 = yymmdd of the software Key to file names: MD50 = ham software for 70 cm MD50 phone MD59 = ham software for 70 cm MD59 phone ME59 = ham software for 23 cm ME59 phone CU53 = with CU53 handset CU59 = with CU59 handset MPTT = M button is PTT SPTT = S button is PTT (available on CU59) NORMAL = Automatic repeater shift according to Finnish repeater band (MD5x) GERMAN = Automatic repeater shift according to German repeater band (MD5x) -these will be made automatic later FINHAM = 432-438 MHz TX on MD5x EUROHAM = 430-440 MHz TX on MD5x, 1240-1300 MHz on ME59 USA = 902-928 MHz TX on ME59 X214 = offset Xtal is 21.4 MHz (MD5x) X314 = offset Xtal is 31.4 MHz (MD5x) X81 = offset VFO is 81 MHz (ME59) X126 = offset VFO is 126 MHz (ME59) PIN = PIN code (3694) is asked at startup NOPIN = No PIN code is asked at startup Select one of each set according to your phone configuration. other definable parameters exist, but are not precomplied. Look for more info from the source code Not all versions are tested - if you find something wrong, please email me At first boot the display may look strange, just tap 00# and see if anything happens... Repeater shifts may be also strange, see above what the various signs mean and type commands from below accordingly. Commands: 0# restore memory 0 1# restore memory 1 ... 9# restore memory 9 69# try it you'll like it 70# store memory 0 71# store memory 1 ... 79# store memory 9 80# debug info (if compiled with debug option) 81# repeater channels included in scan 82# simplex channels included in scan 84# when battery operated, lights on permanently / timer controlled 85# clear all scanner rejects 86# positive/negative duplex toggle 87# repeater duplex toggle 7.6/1.6 MD5x and 28.0/6.0 ME59 88# display test (active until # is released) 89# shows the sw info: the offset vco/xtal, defined repeater band, handset and the tx band limits (active until # is released) Finland = 432-438 Euro = 430-440 90# power level 0 91# power level 1 92# power level 2 93# power level 3 94# duplex/simplex toggle 95# reject selected channel from scan 99# try it you won't like it HF scan (also hidden feature for display segment testing) * 1750 Hz repeater beep STO one channel up o-o one channel down CL backspace CS power level toggle 0/1/2/3 M PTT (squelch on SPTT version) S squelch (PTT on SPTT version) R duplex/simplex toggle - reject this channel when scanning + increase volume - decrease volume when scanning, R rejects the channel and CL clears all rejects ToDo: - automatic repeater shift - 12.5 kHz step for MD5x Known bugs: - on German version, higher repeater channels cannot be setwith 2 digits as E.g. 88# is interpreted as display test command End of the short info text by OH3NWQ http://www.funet.fi/~oh3nwq/oh3nwq.html mailto:oh3nwq@nic.funet.fi